Engine bay bulkhead

Light at the end of the tunnel! The gelcoat repair work has been quite a monotonous task. I quite enjoyed doing the flash lines and general polishing stuff since after a bit of practice I was starting to get a reasonable technique and a finish that i was quite happy with. The more complicated areas however proved to be a real challenge that I hadn’t been expecting. Areas of the gelcoat where quite thin and the glass strand/mat layers could be seen on the surface in some places, to make matters worse the thinnest area of gelcoat was right on the front of the car around the radiator opening in front of the bonnet. I sought advice down many avenues and the conclusion was pretty much all the same – that’s not gonna be easy to fix!…. and it wasn’t! One thing I now understand about gelcoat is it wasn’t designed to be used in air and especially not in very fine layers. Gelcoat is supposed to be laid up in a mould. The side that you eventually see is therefore immediately sealed from the air as it is applied to the mould. The opposite side (the open to the air side) is designed (chemically) to remain tacky or soft for a considerable time, this is to allow a chemical bond to take place between it and the following layups of gelcoat or resin and matts. Thus when you are using gel coat to do small thin cover up repairs it is technically not being used the way it was chemically engineered. The way to solve this is to cover up the repairs as you apply them with a thin polyester film, this works very well for very small spot repairs on flat or external curved areas but does not provide a solution for larger areas or internal radius areas. Flow coat can also be used since flow coat is essentially gelcoat with a bit of wax added. The wax is designed/intended to come to the surface during the set and form a seal from the air and thus allow the cure, however flow coat is again not suitable for very fine layer application. In the end after numerous attempts and almost giving up ( surrendering to a paint job) I found (actually it was Kevin’s idea) a technique that worked. A combination of help from an old friend, who is good with an airbrush,(thanks Kevin – I shall be buying that man a beer or two) and trusty old youtube where I found the best method of covering thinly applied layers of gelcoat  – basically  -Wait an hour then paint over with PVA.  Kevin would paint over the repair areas with several very fine layers of acetone thinned gelcoat using an airbrush, this allowed the repair to sit very smooth and be feathered off at the edges which would mean minimal sanding afterwards(the minimal sanding is the essential bit to aim for). Then after approx an hour or once the coats had dried sufficiently to just quicky paint over the whole area with general duty PVA ( a water based adhesive widely available from any builders merchants, plasterers use it before skimming ceilings and walls to enhance the bond) but here its not being used to help with any bonding, its merely being used to completely seal the surface from the air which allows it to cure as if it were face down in a mould.. Then next morning the pva simply washes off with warm/hot water and light sanding can commence. (1200 or 1500 grit) before compound polish.20160727_153239

Used the same technique on the dreaded bulkhead.

At last now I can get on – the body under seal will be going on in the next few days and I can be planning the body on to chassis soon. Back to the real car building stuff hooray!





Garage Meet

Got to meet a few local cobra owners last Sunday. Malcolm Tommy John and Bob came over to meet up in their cobras to offer some guidance it was good to see a few complete cars together, thanks for the visit and the inspiration. I should have taken a few more pictures but managed to get this one of Tommys AK cobra on the drive together with my part built GD, what a terrific job Tommy from Newcastle has done a really smart looking car – ticks all the boxes. I was lucky enough to get taken for a spin along the coast road – that thing sure does shift – it certainly goes as quick as it looks. Thanks for the ride!

garage meet

Tommy’s car has a Chevy v8 producing a fantastic v8 rumble and awesome amounts of torque – it seemed almost too quick – what secrets did he have under the bonnet.


I’m sure that’s cheating……